Do you need insulation in your home, and you’re looking for more information on a more traditional insulation like cellulose?
RetroFoam of Michigan has been in the foam insulation game for more than 15 years. We also know quite a bit about traditional insulations like cellulose. As part of RetroFoam of Michigan’s ongoing efforts to be transparent while educating our customers we are here to answer questions about cellulose insulation.
What is Cellulose Insulation?
Cellulose insulation is the oldest form of home insulation. It can be either a loose-fill or blown-in insulation and can be used in both new and existing homes.
Typical places to use cellulose is in enclosed existing walls, open new walls, and unfinished attic floors. It is primarily made from recycled newsprint. These small particles form an insulation material that conforms to most spaces without disturbing the structure or finish.
How Cellulose Insulation Works
Cellulose insulation can be used in both existing homes and new construction. It can be blown as loose fill insulation in attic cavities, dense packed into walls and floors, or wet spray for new construction that helps increase heat retention and has the potential to dampen noise levels, according to the Energy Audit Blog.
Dense pack cellulose is used more commonly today for adding retrofit insulation. The dense packing into the wall cavities adds a thermal insulation while providing some level of sound proofing.
Wet spray cellulose has water added to it during the application process. The material has the same thermal and sound retardant properties as dense packing, according to the blog. Wet spray cellulose is almost always installed in new construction before the drywall is put up.
What is R-Value?
R-Value is the capacity of an insulating material’s resistance to heat flow. Basically, that means the higher the R-Value, the greater the insulating power of the material. While R-Value is something that is good to know, it’s not the revered determiner for all things insulation.
Reducing insulation to a number doesn’t tell the whole story, since heat flows in and out through radiation and convection. Heat loss through convection, or air flow, can account for nearly 40 percent of total energy loss in the home. This is an issue if you are only using R-Value to choose your insulation.
What is Cellulose Insulation Made of?
Modern cellulose insulation is made from either 75 to 85 percent ground up recycled paper or recycled denim. It is heavily treated – around 15 percent by volume – with boric acid, borax or ammonium sulfate. While these chemicals aren’t known to be hazardous to people, they can be effective flame retardants and help reduce issues with pests.
Pros and Cons of Cellulose Insulation
- Cellulose has more recycled material than any other commercially available insulation.
- Cellulose doesn’t use any greenhouse gases as propellants.
- When blown into stud cavities cellulose gets into all the nooks and crannies.
- Cellulose is very inexpensive.
- Boric acid, borax or aluminum sulfate used in cellulose insulation provide resistance to mold, pests, and fire.
- During the early 1970s retrofits, loose fill cellulose was used for filling empty wall cavities. Due to blower machine limitations, the material compressed and settled leaving wide gaps in the wall cavities.
- Modern cellulose settles up to 20 percent, which is problematic in relation to closed cavities causing the home to be uncomfortable and energy bills to rise, according to House Energy.
- Cellulose must be kept dry as it absorbs up to 130 percent water by weight.
- It dries very slowly after absorbing water, causing it to deteriorate and settle afterwards.
- After cellulose insulation absorbs water, the chemical fire treatment is destroyed.
- Dense packed cellulose gets everywhere spilling into the house through any openings in the wall cavity.
- Homes with furnace duct systems can expect some of the cellulose dust to be recirculated through the house.
- Cellulose weighs several times as much as fiberglass, which isn’t an issue unless insulating an attic slope.
Process of Installing Cellulose Insulation
Cellulose insulation can be installed by one of two techniques. It can be blown-in – loose fill or dense pack. It can also be spray applied with moisture added.
The dry blown insulation can be installed using a machine to blow the cellulose into the area to be insulated.
In existing homes, installers will remove a strip of exterior siding around waist high. They will then drill a row of three inch holes – one into each stud cavity. A special filler tube is then inserted and the insulation is blown-in filling the cavity. When installation is completed, the holes are sealed with a plug and the siding is replaced.
For new construction, cellulose can be either damp-sprayed or installed dry behind netting, according to the U.S. Department of Energy.
When cellulose is damp sprayed, a small amount of moisture is added at the spray nozzle tip, adding natural starches in the material causing it to adhere to the cavity.
How Does Cellulose Insulation Affect Energy Cost?
Heating and cooling a house accounts for 50 to 70 percent of the energy used in the average American home.
Traditional forms of insulation – like cellulose – is resistant to heat transfer, but tends to poorly protect against air flow. This will contribute to the discomfort in the home, as well as energy loss.
Getting Started with a Free Estimate
Now that you have learned about cellulose insulation, you may you be curious about the benefits of foam insulation and how it is a superior insulator that also acts as an air seal.
If you live in Michigan’s lower peninsula and are ready to schedule a free in-home estimate give us a call at 866-900-3626, or fill out the form on our website.